Видео

Nice video. where can I buy the 3d print file for the accessories ?

Nice and easy to follow 👍

Just got a new co2 laser, this video saved me so much troubleshooting time

In refernce to your 100 watt laser, did you have to run any special electrical to plug it into? All my shop outlets are on 20amp circuits...i know Thunder lasers require special outlets...just curious about Omtech...youve sold me on Omtech!!

🎉🎉🎉🎉 love it thank you

Thank you so much for all your videos, it has been helping me a lot in setting up my AF2028-80W. Do you have any videos showing how to use the side doors? If you put a long piece of wood on the side doors, it doesn't touch the bed and if you bring the bed up, you can't level the laser. What am I doing wrong?

I have the 80w Pro and although I don't need any yet I decided to look for vids to see if there were any pro videos out there on this and Im so glad I found your video so that I can get new mirrors and a lens so I have them just in case my mirrors do the same thing! Thanks for the discount code also!!

Hey. So I attempted the reverse alignment. Everyone I put the alignment tool in and tighten it, it points at a different spot on mirror 2. It does not go into the barrel the same way every time. So this makes it extremely difficult to get an accurate alignment since I mark with a Sharpie where the dot is, then remove the tool so I can pulse. Then we I reinsert the tool it’s not in the exact same spot because of tolerances. Any suggestions? To me there’s no way to get a perfect alignment if the tool can’t be pointing in the same angle every time. It has a very minute wiggle that causes a angle change causing the dot to not be consistent

Hey, another question for ya! I just watched you do a whole traditional alignment and it was spot on. But then you started a reverse alignment with the AP tool and you had to completely redo the alignment because the red dot wasn't hitting your traditional alignment marks? I have the reverse alignment tool and the beam seems to be nowhere near my current traditional alignment.

Great video. Question, when you pulsed mirror 1 straight from the tube I saw your pulse looks like a pretty small sharp dot. My pulse from my tube comes out more like a wider 3-4mm circle. How is your pulse so small? Almost looks like its a focused pulse out of the tube.

very clear description. but why on earth would you use the top meaning a high chance of errors by making the logic opposite to the work area its like using a difficult imperial system when metric is far simpler as shown by US money

on t=7:00 after you had align at the middle of the logo did you roll it back 94mm by hand?

One of the best alignment explanations I have seen.

I know you sped this up, but what was the actual engrave time on the coins for both sides? Great video.

DUDE! Thanks for giving a more (hmm techie) verison of LightBurn. I'm not much of an artist, but computers are my home. Thanks

This is AWEsome.

Lightburn is horrible. It will not cut files!

Thank you that was very helpful 😊

Very smart!! Do you know how to do this on an Epilog Helix 60watt? I think the magnets need to be covered but is there a trick to it? I have a piece of wood to engrave that is too large to close the front door but the top of it shuts. Thanks in advance if you have any suggestions 🙂

I watched your air assist upgrade on your previous machine. I. just got the 80w Pro and was wondering if you upgraded your air assist on that? If so do you have a video? The lay out on these machines are different and I am struggling a bit to get this done. Thanks!!

I have the same machine but my problem is with cutting settings . It cuts and do soldering in the same time. The laser goes through to the other side, but it's impossible to pop out the the cut peice

Love the design, how do you get it too make multiple of something in one go? I can't figure that out so doing singles and losing the will too live with batches

hi, how did you disconnect the built in air pump on your Omtech CO2 laser? I am using the hose from it to the laser head, but the pump still runs.

Hi, this is great, thank you. I didn't see you mention what lens size you are using with all your settings. Could you please share? Much appreciated!

I have to replace my air compressor the one I have started leaking. How do I know which one to buy? How many psi should I d I get? I have 80w omtech

What wood do you use? I'm STRUGGLING. Im using wood that's cheap from Menards

Is there a way to test my IOT Relay? I checked in the "Machine inspector 30=1" but in spindle control I don't see "Automatic", I only see "Manual or Hardware" Any idea what is my problem here, my setup or my IOT Relay?

Where can I find out your source for these coins? I can’t find it.

This is the kind of video I was looking for. I am new to Fiber Lasers and this video answered so many questions. Keep these coming for people like me.

Masterful. It was really hard to keep my eyes off of the guy in the bottom right corner.

Great video!! Helps me out a lot.

So I am just starting sublimation. when I import my image which I saved as a pdf from word, the targets are fine but the outline is teensy tiny and off ctr. Also I should be able to place my sublimated piece anywhere on the bed correct?

thanks very informative, one question how thick plywood can a 100w laser cut in one pass?

Why would double lines happen all of a sudden though? If your machine was engraving fine one day, why would it just go off center the next day if its a software issue?

Can you do a video on how to tighten up all the nuts and bolts and also how to tighten the belt?

Hey man. It looks like your affiliate code has reached its limit of uses and isn't working anymore. Just wanted to let you know.

Very good use case for the camera. Lightburn cameras never seemed accurate enough for me because I would see people putting a circular logo on a circular coaster and if that thing is not PERFECT, it is going to look terrible. But using it to easily squeeze out all the space on a sheet where you assume you might be 1 or 2 mm off, it works great for that. I think having it so far up with your lid open also really helps as you don't have to deal as much with wide angles.

To be clear, if you have the reverse alignment laser tool, you would just do the second part and not have to do the initial part, right? I am surprised that the front co2 laser bracket does not have left/right up/down threads to fine adjust the tube alignment on these machines. Sure shimming kinda works, but often people are sticking postit notes or paper as shims and over time things like that will compress and get thinner and the alignment will drift. I guess the same thing would happen with rubber grips touching the glass as well, but it would be easier I think to periodically align it.

OMG, THAT is what that thing I saw on the omtech site is for. I thought it was some kind of inline red dot and it made NO DANG sense. NOW I get it. Have not seen one of these alignment videos that was not doing the painters tape and pulse method. I am in that obsessive stage that I always get in when buying a new piece of tech.

Are these offsets consistent on both x and y axis?

Great video, do these settings live in lightburn or are they uploaded into the firmware somewhere. Do most machines come with offsets this far off? Those are some pretty huge offsets it seems. Looking to get into laser cutting (10 year 3d printing background but new to cnc / laser) with a monport or an omtech 50 - 80 watt mid tier unit.

Can that 150 watt be dialed down enough for fine engravings? I heard it’s hard to dial down a high wattage laser

I live in an apartment with smoke detectors everwhere with sprinklers in every room. Would that smoke set off alarms if you're doing a bunch of those patches? Thoughts on an entry level laser?

Can't afford a laser like this. What is a good entry level laser for doing patches for hats? I can upgrade as business builds.

You skipped over the settings you used for each layer. What did you end up using?

How can you do this for the OMTech Pro which has the trocen controller?

Works perfectly exactly how u said thank u

Hi, you use a 100W JPT Mopa M7 right? This Laser has the Option Pulse duration. You have to look into the technical Data first. There you can find the max Ratings depending of the Frequency. You can set the Q Pulse of max Power depending of the Frequency. Example: if you use a Frequency of 70kHz the max Q Pulse is 250ns. At 200kHz the max Q Pulse is 60ns at the max output Power. It means if you set the Power at 50% at 200kHz and 60ns the output Power is 50% or 50W. If you increase the Q Puls from 60 to 200ns the output Power is less than 50% or 50W. If you decrease the Q Puls from 60 to 30 the output Power is also less than your seting of 50% or 50W. The max Q Puls is 2ns at 2.960kHz. At 20kHz it is 350ns. Hope you Understand what i mean.

Close is no cigar show how to make adjustments to fine tune the camera it's not hard to do

Thanks. Does it need to be done again when you replace the lens? I just recently replaced it. Same size just a new one.